	PARKLYN ERVICES	·	RC: 2994849

Does Kaduna Polytechnic Offer Technical Education | POLY Enquiry

facebook Page

WhatsApp Channel

Is Technical Education Offered in Kaduna Polytechnic (KADPOLY)?

If you are planning to study Technical Education at Kaduna Polytechnic located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Kaduna Polytechnic.

Does Kaduna Polytechnic (KADPOLY) offer Technical Education?

No, Kaduna Polytechnic does not offer Technical Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Kaduna Polytechnic (KADPOLY) below to check if the Technical Education course under the Faculty of Education has been updated.

Admission Requirements for Technical Education When Accredited in Kaduna Polytechnic (KADPOLY)

O’Level Requirements

To study this course, candidates seeking admission into the Technical Education department under Faculty of Education, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:

Mathematics or NTC/NBC,
English Language and
any three (3) relevant subjects.

JAMB Subject Combination

Use of English,
Physics,
Mathematics and
Chemistry.

Kaduna Polytechnic Cut-Off Mark for Technical Education

The general UTME cut-off mark is 180, but due to the variation of Technical Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Kaduna Polytechnic Officials. However, to improve your admission chances:

Aim for 180+ score.
Perform well in Post-UTME screening.

Other Kaduna Polytechnic Science Courses with their Requirements

Computer Science (CS)

SSCE Requirements

To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Physics,
Mathematics, and
any two (2) other Science subjects.

Civil Engineering Technology

SSCE Requirements

To study this course, candidates seeking admission into the Civil Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:

English Language,
Mathematics,
Physics, Chemistry and
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.

Building Technology (BT)

SSCE Requirements

To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

Mathematics,
English Language,
Physics, Chemistry and
any one of
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.

Quantity Surveying (QS)

SSCE Requirements

To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:

English Language,
Mathematics,
Physics,
Chemistry and
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.

Mechanical Engineering Technology

SSCE Requirements

To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Mathematics,
Physics, Chemistry and
any one subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.

Architectural Technology

SSCE Requirements

To study this course, the minimum requirement for applicants seeking admission to the Architectural Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:

English Language,
Mathematics,
Physics and
any two subjects from:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.

Surveying and Geoinformatics

SSCE Requirements

To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:

English Language,
Mathematics,
Chemistry and Physics,
any one (1) from
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.