If you are planning to study Science Laboratory Technology (SLT) at Kaduna State University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KASU.
Does Kaduna State University (KASU) offer Science Laboratory Technology?
No, Kaduna State University does not offer Science Laboratory Technology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Kaduna State University (KASU) below to check if the Science Laboratory Technology course under the Faculty of Science has been updated.
Admission Requirements for Science Laboratory Technology (SLT) When Accredited in Kaduna State University (KASU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
JAMB Subject Combination
Any other three (3) relevant subjects (Mathematics, Biology / Agricultural Science, or Physics)
KASU Cut-Off Mark for Science Laboratory Technology (SLT)
The general UTME cut-off mark is 180, but due to the variation of Science Laboratory Technology (SLT) cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KASU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KASU Science Courses with their Requirements
Environmental Management
SSCE Requirements
To study this course, candidates seeking admission into the Environmental Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other four (4) relevant subjects plus a pass in English Language.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Industrial Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
Education and Mathematics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Mathematics department.
one (1) other Science subject, and
any other relevant subjects.
Pharmacy
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Pharmacy department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Education and Physics
SSCE Requirements
To study this course, candidates seeking admission into the Education and Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects or NTC / NBC.
Nigerian Universities Offering Science Laboratory Technology Course