If you are planning to study Human Kinetics and Health Education at Kano State Polytechnic located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KANOPOLY.
Does Kano State Polytechnic (KANOPOLY) offer Human Kinetics and Health Education?
No, Kano State Polytechnic does not offer Human Kinetics and Health Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Kano State Polytechnic (KANOPOLY) below to check if the Human Kinetics and Health Education course under the Faculty of Education has been updated.
Admission Requirements for Human Kinetics and Health Education When Accredited in Kano State Polytechnic (KANOPOLY)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Human Kinetics and Health Education department under Faculty of Education, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any three (3) other relevant subjects.
JAMB Subject Combination
any two (2) relevant subjects.
KANOPOLY Cut-Off Mark for Human Kinetics and Health Education
The general UTME cut-off mark is 230, but due to the variation of Human Kinetics and Health Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KANOPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KANOPOLY Science Courses with their Requirements
Architectural Technology
SSCE Requirements
To study this course, candidates seeking admission into the Architectural Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Printing Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Printing Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
Mechatronics Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechatronics Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
and any one other subject from:
Biology / Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics / Commerce.
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Welding and Fabrication Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Nigerian Tertiary Institutions Offering Human Kinetics and Health Education Course