If you are planning to study Industrial Engineering at Kano State University of Science and Technology located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KUST.
Does Kano State University of Science and Technology (KUST) offer Industrial Engineering?
No, Kano State University of Science and Technology does not offer Industrial Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kano State University of Science and Technology (KUST) below to check if the Industrial Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Engineering When Accredited in Kano State University of Science and Technology (KUST)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Engineering department under Faculty of Engineering / Technology.
any other Science subject.
KUST Cut-Off Mark for Industrial Engineering
The general UTME cut-off mark is 180, but due to the variation of Industrial Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KUST Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Education and Physics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Education and Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subjects or NTC / NBC.
Agricultural Science and Education
SSCE Requirements
To study this course, candidates seeking admission into the Agricultural Science and Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
any other relevant subject.
Electrical / Electronics Education
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronics Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural Engineering (AE) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Industrial Engineering Course