
If you are planning to study Mechanical and Metallurgical Engineering at Kano State University of Science and Technology located in Kano State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KUST.
Does Kano State University of Science and Technology (KUST) offer Mechanical and Metallurgical Engineering?
No, Kano State University of Science and Technology does not offer Mechanical and Metallurgical Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kano State University of Science and Technology (KUST) below to check if the Mechanical and Metallurgical Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical and Metallurgical Engineering When Accredited in Kano State University of Science and Technology (KUST)
O’Level Requirements
To study this course, candidates seeking admission into the Mechanical and Metallurgical Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) other Science subject.
KUST Cut-Off Mark for Mechanical and Metallurgical Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechanical and Metallurgical Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KUST Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KUST Science Courses with their Requirements
Biology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biology department.
Mathematics / Physics and
any one other relevant subject.
Civil Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Civil Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Geology department.
any other relevant subject.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Environmental Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Education and Mathematics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Mathematics department.
one (1) other Science subject, and
any other relevant subjects.
Nigerian Tertiary Institutions Offering Mechanical and Metallurgical Engineering Course