If you are planning to study Computer Engineering at Kebbi State University of Science and Technology located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KSUSTA.
Does Kebbi State University of Science and Technology (KSUSTA) offer Computer Engineering?
No, Kebbi State University of Science and Technology does not offer Computer Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kebbi State University of Science and Technology (KSUSTA) below to check if the Computer Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Computer Engineering When Accredited in Kebbi State University of Science and Technology (KSUSTA)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
KSUSTA Cut-Off Mark for Computer Engineering
The general UTME cut-off mark is 180, but due to the variation of Computer Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KSUSTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KSUSTA Science Courses with their Requirements
Zoology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Zoology department.
two (2) other Science subject.
Physics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics department.
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
Education and Physics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Physics department.
two (2) other Science subjects or NTC / NBC.
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Metalwork Technology Education
SSCE Requirements
To study this course, candidates seeking admission into the Metalwork Technology Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science, Physics, or Chemistry
and two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
Mathematics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Building
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Universities Offering Computer Engineering Course