If you are planning to study Crop Production and Soil Science at Kebbi State University of Science and Technology located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KSUSTA.
Does Kebbi State University of Science and Technology (KSUSTA) offer Crop Production and Soil Science?
No, Kebbi State University of Science and Technology does not offer Crop Production and Soil Science under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Kebbi State University of Science and Technology (KSUSTA) below to check if the Crop Production and Soil Science course under the Faculty of Agriculture has been updated.
Admission Requirements for Crop Production and Soil Science When Accredited in Kebbi State University of Science and Technology (KSUSTA)
O’Level Requirements
To study this course, candidates seeking admission into the Crop Production and Soil Science department under Faculty of Agriculture, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics.
KSUSTA Cut-Off Mark for Crop Production and Soil Science
The general UTME cut-off mark is 180, but due to the variation of Crop Production and Soil Science cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KSUSTA Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KSUSTA Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Education and Mathematics
SSCE Requirements
To study this course, candidates seeking admission into the Education and Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) other Science subject, and
any other relevant subjects.
Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Building
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Biological Science
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Biological Science department.
Any other relevant Science subject.
Applied Chemistry
SSCE Requirements
To study this course, candidates aspiring to gain admission into Applied Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Metalwork / Woodwork Technology Education
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Metalwork / Woodwork Technology Education department.
Physics / Chemistry, Biology or Agricultural Science;
Physics / Chemistry, Biology or Agricultural Science;
General Science / Integrated Science, Technical Drawing / Fine Art, Health Science Food and Nutrition, Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
Nigerian Tertiary Institutions Offering Crop Production and Soil Science Course