If you are planning to study Orthopaedic and Plaster Technology at Kenule Beeson Saro-Wiwa Polytechnic formally known as Rivers State Polytechnic (RIVPOLY) located in Rivers State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into KENPOLY.
Does Kenule Beeson Saro-Wiwa Polytechnic (KENPOLY) offer Orthopaedic and Plaster Technology?
No, Kenule Beeson Saro-Wiwa Polytechnic does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Kenule Beeson Saro-Wiwa Polytechnic (KENPOLY) below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Kenule Beeson Saro-Wiwa Polytechnic (KENPOLY)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
KENPOLY Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from KENPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other KENPOLY Science Courses with their Requirements
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course