If you are planning to study Ceramics Technology at Kogi State Polytechnic located in Kogi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Kogi State Polytechnic.
Does Kogi State Polytechnic offer Ceramics Technology?
No, Kogi State Polytechnic does not offer Ceramics Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kogi State Polytechnic below to check if the Ceramics Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Ceramics Technology When Accredited in Kogi State Polytechnic
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Ceramics Technology department under Faculty of Engineering / Technology.
Biology/Agricultural Science/Mathematics,
Biology/Agricultural Science, Woodwork,
Metalwork, Technical/Engineering Drawing,
Geography, Fine Art, Further Mathematics,
Fine Art, Economics Basic Electricity and
a minimum of pass grade in English Language.
Kogi State Polytechnic Cut-Off Mark for Ceramics Technology
The general UTME cut-off mark is 180, but due to the variation of Ceramics Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Kogi State Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Kogi State Polytechnic Science Courses with their Requirements
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates seeking admission into the Urban and Regional Planning (URP) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronic Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science Subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Foundry Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Foundry Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Tertiary Institutions Offering Ceramics Technology Course