If you are planning to study Welding and Fabrication Technology at Kogi State Polytechnic located in Kogi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Kogi State Polytechnic.
Does Kogi State Polytechnic offer Welding and Fabrication Technology?
No, Kogi State Polytechnic does not offer Welding and Fabrication Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Kogi State Polytechnic below to check if the Welding and Fabrication Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Welding and Fabrication Technology When Accredited in Kogi State Polytechnic
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Welding and Fabrication Technology department under Faculty of Engineering / Technology.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
JAMB Subject Combination
Physics/Technical Drawing or Chemistry.
Kogi State Polytechnic Cut-Off Mark for Welding and Fabrication Technology
The general UTME cut-off mark is 180, but due to the variation of Welding and Fabrication Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Kogi State Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Kogi State Polytechnic Science Courses with their Requirements
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronic Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science Subject.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Civil Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering Technology department.
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Foundry Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Foundry Engineering Technology department.
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Nigerian Polytechnics Offering Welding and Fabrication Technology Course