If you are planning to study Crop Production Technology at Modibbo Adama University Of Technology located in Adamawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into MAUTECH.
Does Modibbo Adama University Of Technology (MAUTECH) offer Crop Production Technology?
No, Modibbo Adama University Of Technology does not offer Crop Production Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Modibbo Adama University Of Technology (MAUTECH) below to check if the Crop Production Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Crop Production Technology When Accredited in Modibbo Adama University Of Technology (MAUTECH)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Crop Production Technology department under Faculty of Agriculture.
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics.
MAUTECH Cut-Off Mark for Crop Production Technology
The general UTME cut-off mark is 180, but due to the variation of Crop Production Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from MAUTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other MAUTECH Science Courses with their Requirements
Chemical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Chemical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Civil Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Forestry and Wildlife Management
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Forestry and Wildlife Management department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Further Mathematics and Statistics.
Plant Science
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Plant Science department.
Building
SSCE Requirements
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Crop Production Technology Course