If you are planning to study Mechanical Metalwork Technology Education at Modibbo Adama University Of Technology located in Adamawa State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into MAUTECH.
Does Modibbo Adama University Of Technology (MAUTECH) offer Mechanical Metalwork Technology Education?
No, Modibbo Adama University Of Technology does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Modibbo Adama University Of Technology (MAUTECH) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Modibbo Adama University Of Technology (MAUTECH)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
MAUTECH Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from MAUTECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other MAUTECH Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Crop Production and Horticulture
SSCE Requirements
To study this course, candidates seeking admission into the Crop Production and Horticulture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics.
Microbiology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Microbiology department.
Mathematics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics department.
any two (2) other relevant subjects.
Education and Mathematics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education and Mathematics department.
one (1) other Science subject, and
any other relevant subjects.
Education / Mechanical Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Education / Mechanical Technology department.
and one (1) of Biology, Agricultural Science, Physics, or Chemistry,
General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Building,
Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Electrical Electronic, Metal Work and Wood Work.
Mechanical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course