If you are planning to study Printing Technology at Nuhu Bamalli Polytechnic located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into NUBAPOLY.
Does Nuhu Bamalli Polytechnic (NUBAPOLY) offer Printing Technology?
No, Nuhu Bamalli Polytechnic does not offer Printing Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Nuhu Bamalli Polytechnic (NUBAPOLY) below to check if the Printing Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Printing Technology When Accredited in Nuhu Bamalli Polytechnic (NUBAPOLY)
O’Level Requirements
To study this course, candidates seeking admission into the Printing Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
JAMB Subject Combination
Chemistry or Technical Drawing / Art.
NUBAPOLY Cut-Off Mark for Printing Technology
The general UTME cut-off mark is 180, but due to the variation of Printing Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from NUBAPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other NUBAPOLY Science Courses with their Requirements
Mechanical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Computer Science (CS)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Civil Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering Technology department.
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Nigerian Polytechnics Offering Printing Technology Course