If you are planning to study Mathematics and Education Technology at Obafemi Awolowo University located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into OAU.
Does Obafemi Awolowo University (OAU) offer Mathematics and Education Technology?
No, Obafemi Awolowo University does not offer Mathematics and Education Technology under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Obafemi Awolowo University (OAU) below to check if the Mathematics and Education Technology course under the Faculty of Education has been updated.
Admission Requirements for Mathematics and Education Technology When Accredited in Obafemi Awolowo University (OAU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics and Education Technology department under Faculty of Education.
three (3) more pertinent science subjects in not more than two (2) sittings.
JAMB Subject Combination
one (1) other Science Subject.
OAU Cut-Off Mark for Mathematics and Education Technology
The general UTME cut-off mark is 180, but due to the variation of Mathematics and Education Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from OAU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other OAU Science Courses with their Requirements
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Computer Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Medical Rehabilitation
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medical Rehabilitation department.
Zoology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Zoology department.
two (2) other Science subject.
Teacher Education Science
SSCE Requirements
To study this course, candidates aspiring to gain admission into Teacher Education Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Engineering (AE) department.
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Mathematics and Education Technology Course