If you are planning to study Printing Technology at Ogun State Institute of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into OGITECH.
Does Ogun State Institute of Technology (OGITECH) offer Printing Technology?
No, Ogun State Institute of Technology does not offer Printing Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Ogun State Institute of Technology (OGITECH) below to check if the Printing Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Printing Technology When Accredited in Ogun State Institute of Technology (OGITECH)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Printing Technology department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
JAMB Subject Combination
Chemistry or Technical Drawing / Art.
OGITECH Cut-Off Mark for Printing Technology
The general UTME cut-off mark is 180, but due to the variation of Printing Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from OGITECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other OGITECH Science Courses with their Requirements
Computer Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronic Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science Subject.
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Estate Management and Valuation
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Estate Management and Valuation department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Architectural Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architectural Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Nigerian Polytechnics Offering Printing Technology Course