If you are planning to study Surveying and Geoinformatics at Ogun State Institute of Technology located in Ogun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into OGITECH.
Does Ogun State Institute of Technology (OGITECH) offer Surveying and Geoinformatics?
No, Ogun State Institute of Technology does not offer Surveying and Geoinformatics under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Ogun State Institute of Technology (OGITECH) below to check if the Surveying and Geoinformatics course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Surveying and Geoinformatics When Accredited in Ogun State Institute of Technology (OGITECH)
O’Level Requirements
To study this course, candidates seeking admission into the Surveying and Geoinformatics department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
JAMB Subject Combination
Chemistry, Geography, Art, Biology and Economics.
OGITECH Cut-Off Mark for Surveying and Geoinformatics
The general UTME cut-off mark is 180, but due to the variation of Surveying and Geoinformatics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from OGITECH Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other OGITECH Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Computer Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Computer Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Nigerian Polytechnics Offering Surveying and Geoinformatics Course