If you are planning to study Metallurgical and Material Engineering at Ondo City Polytechnic, Adegoke, Arigbabola located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ODCITYPOLY.
Does Ondo City Polytechnic, Adegoke, Arigbabola (ODCITYPOLY) offer Metallurgical and Material Engineering?
No, Ondo City Polytechnic, Adegoke, Arigbabola does not offer Metallurgical and Material Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Ondo City Polytechnic, Adegoke, Arigbabola (ODCITYPOLY) below to check if the Metallurgical and Material Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical and Material Engineering When Accredited in Ondo City Polytechnic, Adegoke, Arigbabola (ODCITYPOLY)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Metallurgical and Material Engineering department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one other Science subject.
ODCITYPOLY Cut-Off Mark for Metallurgical and Material Engineering
The general UTME cut-off mark is 180, but due to the variation of Metallurgical and Material Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ODCITYPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ODCITYPOLY Science Courses with their Requirements
Dental Nursing Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Dental Nursing Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Mechanical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
Estate Management and Valuation
SSCE Requirements
To study this course, candidates aspiring to gain admission into Estate Management and Valuation department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Computer Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Computer Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Orthopaedic and Plaster Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Orthopaedic and Plaster Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Nigerian Tertiary Institutions Offering Metallurgical and Material Engineering Course