If you are planning to study Welding and Fabrication Technology at Ondo City Polytechnic, Adegoke, Arigbabola located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ODCITYPOLY.
Does Ondo City Polytechnic, Adegoke, Arigbabola (ODCITYPOLY) offer Welding and Fabrication Technology?
No, Ondo City Polytechnic, Adegoke, Arigbabola does not offer Welding and Fabrication Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Ondo City Polytechnic, Adegoke, Arigbabola (ODCITYPOLY) below to check if the Welding and Fabrication Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Welding and Fabrication Technology When Accredited in Ondo City Polytechnic, Adegoke, Arigbabola (ODCITYPOLY)
O’Level Requirements
To study this course, candidates seeking admission into the Welding and Fabrication Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
JAMB Subject Combination
Physics/Technical Drawing or Chemistry.
ODCITYPOLY Cut-Off Mark for Welding and Fabrication Technology
The general UTME cut-off mark is 180, but due to the variation of Welding and Fabrication Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ODCITYPOLY Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ODCITYPOLY Science Courses with their Requirements
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Public Health Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Public Health Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Estate Management and Valuation
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Estate Management and Valuation department.
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Electrical / Electronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Environmental Health Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Environmental Health Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
At least a pass in English Language
Biology/Health Science and
any three (3) relevant subjects from the following:
Physics, Food and Nutrition/Home Management,
Nigerian Language, Religious Studies, Economics,
Nutrition, Chemistry, Geography and
at least a pass in English Language.
Nigerian Polytechnics Offering Welding and Fabrication Technology Course