If you are planning to study Nutrition and Dietetics at Petroleum Training Institute, Effurun located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into PTI.
Does Petroleum Training Institute, Effurun (PTI) offer Nutrition and Dietetics?
No, Petroleum Training Institute, Effurun does not offer Nutrition and Dietetics under its Faculty of Health and Medical Sciences. However, since our course list is updated regularly, you can visit the courses available at Petroleum Training Institute, Effurun (PTI) below to check if the Nutrition and Dietetics course under the Faculty of Health and Medical Sciences has been updated.
Admission Requirements for Nutrition and Dietetics When Accredited in Petroleum Training Institute, Effurun (PTI)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Nutrition and Dietetics department under Faculty of Health and Medical Sciences.
Biology/Agricultural Science.
PTI Cut-Off Mark for Nutrition and Dietetics
The general UTME cut-off mark is 230, but due to the variation of Nutrition and Dietetics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from PTI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other PTI Science Courses with their Requirements
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Industrial Safety and Environmental Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Industrial Safety and Environmental Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) subjects from:
Biology/Agricultural Science, Technical Drawing,
Basic Electronics / Basic Electricity,
Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.),
Further Mathematics, Geography, Economics / Commerce.
Petroleum Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Petroleum Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any one (1) Science subject.
Mechanical Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Petroleum and Gas Processing
SSCE Requirements
To study this course, candidates aspiring to gain admission into Petroleum and Gas Processing department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) relevant subjects from:
Biology/Agricultural Science, Technical Drawing,
Basic Electronics/Basic Electricity, Auto Mechanics,
Metal Work, Woodwork for Civil Engineering Technology,
Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering 'O' Level pass in Biology is required.
Welding and Fabrication Technology
SSCE Requirements
To study this course, candidates seeking admission into the Welding and Fabrication Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Nigerian Polytechnics Offering Nutrition and Dietetics Course