If you are planning to study Surveying and Geoinformatics at Petroleum Training Institute, Effurun located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into PTI.
Does Petroleum Training Institute, Effurun (PTI) offer Surveying and Geoinformatics?
No, Petroleum Training Institute, Effurun does not offer Surveying and Geoinformatics under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Petroleum Training Institute, Effurun (PTI) below to check if the Surveying and Geoinformatics course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Surveying and Geoinformatics When Accredited in Petroleum Training Institute, Effurun (PTI)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
JAMB Subject Combination
Chemistry, Geography, Art, Biology and Economics.
PTI Cut-Off Mark for Surveying and Geoinformatics
The general UTME cut-off mark is 180, but due to the variation of Surveying and Geoinformatics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from PTI Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other PTI Science Courses with their Requirements
Computer Science (CS)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Mechanical Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Petroleum Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Petroleum Engineering Technology department.
any one (1) Science subject.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Industrial Safety and Environmental Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Safety and Environmental Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) subjects from:
Biology/Agricultural Science, Technical Drawing,
Basic Electronics / Basic Electricity,
Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.),
Further Mathematics, Geography, Economics / Commerce.
Welding and Fabrication Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Welding and Fabrication Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Petroleum and Gas Processing
SSCE Requirements
To study this course, candidates aspiring to gain admission into Petroleum and Gas Processing department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) relevant subjects from:
Biology/Agricultural Science, Technical Drawing,
Basic Electronics/Basic Electricity, Auto Mechanics,
Metal Work, Woodwork for Civil Engineering Technology,
Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering 'O' Level pass in Biology is required.
Nigerian Polytechnics Offering Surveying and Geoinformatics Course