If you are planning to study Orthopaedic and Plaster Technology at Prime Polytechnic, Jida Bassa, Ajaokuta located in Kogi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Prime Polytechnic.
Does Prime Polytechnic, Jida Bassa, Ajaokuta offer Orthopaedic and Plaster Technology?
No, Prime Polytechnic, Jida Bassa, Ajaokuta does not offer Orthopaedic and Plaster Technology under its Faculty of Allied Health Sciences. However, since our course list is updated regularly, you can visit the courses available at Prime Polytechnic, Jida Bassa, Ajaokuta below to check if the Orthopaedic and Plaster Technology course under the Faculty of Allied Health Sciences has been updated.
Admission Requirements for Orthopaedic and Plaster Technology When Accredited in Prime Polytechnic, Jida Bassa, Ajaokuta
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Orthopaedic and Plaster Technology department under Faculty of Allied Health Sciences, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Prime Polytechnic Cut-Off Mark for Orthopaedic and Plaster Technology
The general UTME cut-off mark is 230, but due to the variation of Orthopaedic and Plaster Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Prime Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Prime Polytechnic Science Courses with their Requirements
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Computer Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Civil Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Civil Engineering Technology department.
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Foundry Engineering Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Foundry Engineering Technology department.
at least a pass in English Language,
any two relevant subjects from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Computer Science (CS)
SSCE Requirements
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Nigerian Tertiary Institutions Offering Orthopaedic and Plaster Technology Course