If you are planning to study Software Engineering and Digital Entrepreneurship at Redeemer's University, Nigeria located in Osun State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into RUN.
Does Redeemer's University, Nigeria (RUN) offer Software Engineering and Digital Entrepreneurship?
No, Redeemer's University, Nigeria does not offer Software Engineering and Digital Entrepreneurship under its Faculty of Data and Decision Sciences. However, since our course list is updated regularly, you can visit the courses available at Redeemer's University, Nigeria (RUN) below to check if the Software Engineering and Digital Entrepreneurship course under the Faculty of Data and Decision Sciences has been updated.
Admission Requirements for Software Engineering and Digital Entrepreneurship When Accredited in Redeemer's University, Nigeria (RUN)
O’Level Requirements
To study this course, candidates seeking admission into the Software Engineering and Digital Entrepreneurship department under Faculty of Data and Decision Sciences, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
three (3) other relevant subjects.
JAMB Subject Combination
two (2) other relevant subjects.
RUN Cut-Off Mark for Software Engineering and Digital Entrepreneurship
The general UTME cut-off mark is 180, but due to the variation of Software Engineering and Digital Entrepreneurship cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from RUN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other RUN Science Courses with their Requirements
Industrial Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science.
Applied Biology and Genetics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Applied Biology and Genetics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Applied Geophysics
SSCE Requirements
To study this course, candidates seeking admission into the Applied Geophysics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Mechanical Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant Science subjects.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Microbiology
SSCE Requirements
To study this course, candidates seeking admission into the Microbiology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Software Engineering and Digital Entrepreneurship Course