If you are planning to study Printing Technology at Rufus Giwa Polytechnic, Owo located in Ondo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Rufus Giwa Polytechnic.
Does Rufus Giwa Polytechnic, Owo offer Printing Technology?
No, Rufus Giwa Polytechnic, Owo does not offer Printing Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Rufus Giwa Polytechnic, Owo below to check if the Printing Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Printing Technology When Accredited in Rufus Giwa Polytechnic, Owo
O’Level Requirements
To study this course, candidates seeking admission into the Printing Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other subjects from:
Metal Work, Basic Electricity, Technical Drawing/Fine Art,
Book Keeping and Principles of Accounting, Economics/Commerce,
JAMB Subject Combination
Chemistry or Technical Drawing / Art.
Rufus Giwa Polytechnic Cut-Off Mark for Printing Technology
The general UTME cut-off mark is 180, but due to the variation of Printing Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Rufus Giwa Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Rufus Giwa Polytechnic Science Courses with their Requirements
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Horticultural Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Horticultural Technology department.
any other relevant subjectes.
Production Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Production Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology/Agricultural Science,
any other relevant subject from the following:
Technical Drawing, Physics,
Nigerian Language, Home Economics.
Forestry Technology
SSCE Requirements
To study this course, candidates seeking admission into the Forestry Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Nigerian Polytechnics Offering Printing Technology Course