If you are planning to study Automobile Technology Education at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Automobile Technology Education?
No, The Technical University, Ibadan does not offer Automobile Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Automobile Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Automobile Technology Education When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Automobile Technology Education department under Faculty of Education, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology /Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
TECH-U Cut-Off Mark for Automobile Technology Education
The general UTME cut-off mark is 180, but due to the variation of Automobile Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Physics With Electronics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics With Electronics department.
any other Science subject from Further Mathematics and Biology / Agricultural Science.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Civil Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Civil Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Microbiology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Microbiology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Building Technology (BT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building Technology (BT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Nigerian Tertiary Institutions Offering Automobile Technology Education Course