If you are planning to study Electrical and Electronics Engineering (EEE) at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Electrical and Electronics Engineering?
No, The Technical University, Ibadan does not offer Electrical and Electronics Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Electrical and Electronics Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Electrical and Electronics Engineering (EEE) When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical and Electronics Engineering (EEE) department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
TECH-U Cut-Off Mark for Electrical and Electronics Engineering (EEE)
The general UTME cut-off mark is 180, but due to the variation of Electrical and Electronics Engineering (EEE) cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Biochemistry
SSCE Requirements
To study this course, candidates aspiring to gain admission into Biochemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Microbiology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Microbiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Software Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Software Engineering department.
two (2) other Science subjects.
Mechanical Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mechanical Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant Science subjects.
Nigerian Universities Offering Electrical and Electronics Engineering Course