If you are planning to study Electronics and Computer Engineering at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Electronics and Computer Engineering?
No, The Technical University, Ibadan does not offer Electronics and Computer Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Electronics and Computer Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Electronics and Computer Engineering When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, candidates seeking admission into the Electronics and Computer Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other one (1) relevant subject.
TECH-U Cut-Off Mark for Electronics and Computer Engineering
The general UTME cut-off mark is 180, but due to the variation of Electronics and Computer Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Mathematics
SSCE Requirements
To study this course, candidates seeking admission into the Mathematics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Petroleum Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Petroleum Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Computer Science (CS)
SSCE Requirements
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Biotechnology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Biotechnology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Agricultural Engineering (AE)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Agricultural Engineering (AE) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Electronics and Computer Engineering Course