If you are planning to study Mathematics and Education Technology at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Mathematics and Education Technology?
No, The Technical University, Ibadan does not offer Mathematics and Education Technology under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Mathematics and Education Technology course under the Faculty of Education has been updated.
Admission Requirements for Mathematics and Education Technology When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mathematics and Education Technology department under Faculty of Education, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
three (3) more pertinent science subjects in not more than two (2) sittings.
JAMB Subject Combination
one (1) other Science Subject.
TECH-U Cut-Off Mark for Mathematics and Education Technology
The general UTME cut-off mark is 180, but due to the variation of Mathematics and Education Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Physics With Electronics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physics With Electronics department.
any other Science subject from Further Mathematics and Biology / Agricultural Science.
Cyber Security Science
SSCE Requirements
To study this course, candidates seeking admission into the Cyber Security Science department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Science Laboratory Technology (SLT) department.
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Biomedical Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Biomedical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Food Science and Technology (FT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Food Science and Technology (FT) department.
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Mechanical Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Mechanical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Mathematics and Education Technology Course