If you are planning to study Mechanical Metalwork Technology Education at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Mechanical Metalwork Technology Education?
No, The Technical University, Ibadan does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, candidates seeking admission into the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
TECH-U Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Software Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Software Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
two (2) other Science subjects.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Chemical Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Agricultural Engineering (AE)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Engineering (AE) department.
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Industrial Chemistry
SSCE Requirements
To study this course, candidates seeking admission into the Industrial Chemistry department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology / Agricultural Science.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Science Laboratory Technology (SLT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course