If you are planning to study Polymer Engineering at The Technical University, Ibadan located in Oyo State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into TECH-U.
Does The Technical University, Ibadan (TECH-U) offer Polymer Engineering?
No, The Technical University, Ibadan does not offer Polymer Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at The Technical University, Ibadan (TECH-U) below to check if the Polymer Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Polymer Engineering When Accredited in The Technical University, Ibadan (TECH-U)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Polymer Engineering department under Faculty of Engineering / Technology.
any other Science subject.
TECH-U Cut-Off Mark for Polymer Engineering
The general UTME cut-off mark is 180, but due to the variation of Polymer Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from TECH-U Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other TECH-U Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Chemical Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Chemical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Food Science and Technology (FT)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Food Science and Technology (FT) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subject from;
Biology / Agricultural Science, Physics, Basic Catering and Food Services, Bakery and Confectionaries,
Building Technology (BT)
SSCE Requirements
To study this course, candidates seeking admission into the Building Technology (BT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Statistics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Statistics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other relevant subject.
Mechatronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechatronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Forensic Science
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Forensic Science department.
Nigerian Tertiary Institutions Offering Polymer Engineering Course