If you are planning to study Industrial Technology Education at University of Delta, Agbor located in Delta State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into UNIDEL.
Does University of Delta (UNIDEL), Agbor offer Industrial Technology Education?
No, University of Delta, Agbor does not offer Industrial Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at University of Delta (UNIDEL), Agbor below to check if the Industrial Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Industrial Technology Education When Accredited in University of Delta (UNIDEL), Agbor
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Industrial Technology Education department under Faculty of Engineering / Technology.
three (3) other relevant subjects.
JAMB Subject Combination
one (1) other Science subject.
UNIDEL Cut-Off Mark for Industrial Technology Education
The general UTME cut-off mark is 180, but due to the variation of Industrial Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIDEL Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIDEL Science Courses with their Requirements
Cyber Security
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Cyber Security department.
two (2) other Science subjects.
Biochemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Biochemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Environmental Management and Toxicology
SSCE Requirements
To study this course, candidates seeking admission into the Environmental Management and Toxicology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Statistics
SSCE Requirements
To study this course, candidates seeking admission into the Statistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Physics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Physics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
Architecture
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Tertiary Institutions Offering Industrial Technology Education Course