If you are planning to study Mechanical Metalwork Technology Education at University of Ilorin located in Kwara State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into UNILORIN.
Does University of Ilorin (UNILORIN) offer Mechanical Metalwork Technology Education?
No, University of Ilorin does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at University of Ilorin (UNILORIN) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in University of Ilorin (UNILORIN)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
UNILORIN Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNILORIN Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNILORIN Science Courses with their Requirements
Mechanical Engineering
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Engineering department.
any two (2) other relevant Science subjects.
Education and Biology
SSCE Requirements
To study this course, candidates seeking admission into the Education and Biology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Statistics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Statistics department.
any other relevant subject.
Architecture
SSCE Requirements
To study this course, candidates seeking admission into the Architecture department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Veterinary Medicine
SSCE Requirements
To study this course, candidates aspiring to gain admission into Veterinary Medicine department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Technical Education
SSCE Requirements
To study this course, candidates seeking admission into the Technical Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any three (3) relevant subjects.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course