If you are planning to study Adult and Continuing Education at University of Maiduguri located in Borno State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into UNIMAID.
Does University of Maiduguri (UNIMAID) offer Adult and Continuing Education?
No, University of Maiduguri does not offer Adult and Continuing Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at University of Maiduguri (UNIMAID) below to check if the Adult and Continuing Education course under the Faculty of Education has been updated.
Admission Requirements for Adult and Continuing Education When Accredited in University of Maiduguri (UNIMAID)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Adult and Continuing Education department under Faculty of Education, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Literature in English, History, French, Yoruba, Igbo, Hausa, Christian Religious Studies, Islamic Studies, Geography / Physics, Economics and Government.
For TC II with pass in English Language and
JAMB Subject Combination
one (1) Social Science subject and
UNIMAID Cut-Off Mark for Adult and Continuing Education
The general UTME cut-off mark is 180, but due to the variation of Adult and Continuing Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIMAID Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIMAID Arts Courses with their Requirements
History
SSCE Requirements
To study this course, candidates aspiring to gain admission into History department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any other two (2) relevant Social Sciences or Arts subjects.
Industrial Design
SSCE Requirements
To study this course, candidates aspiring to gain admission into Industrial Design department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any one (1) from: Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing and General Wood Work.
Fine Arts
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Fine Arts department.
Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting, Spray Painting,
Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
Library Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Library Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
three (3) other relevant subjects from:
Arts/Sciences/Social Sciences.
Islamic Studies
SSCE Requirements
To study this course, candidates seeking admission into the Islamic Studies department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Islamic Studies or Arabic and
any three (3) relevant subjects.
Creative Arts
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Creative Arts department.
For holders of NTC, the relevant subjects could be
General Wood work, Building / Engineering Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing,
Printing Origination, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Kanuri
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Kanuri department.
any other three (3) relevant subjects.
Nigerian Tertiary Institutions Offering Adult and Continuing Education Course