If you are planning to study Prosthesis and Orthopaedic Technology at University of Uyo located in Akwa Ibom State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into UNIUYO.
Does University of Uyo (UNIUYO) offer Prosthesis and Orthopaedic Technology?
No, University of Uyo does not offer Prosthesis and Orthopaedic Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at University of Uyo (UNIUYO) below to check if the Prosthesis and Orthopaedic Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Prosthesis and Orthopaedic Technology When Accredited in University of Uyo (UNIUYO)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Prosthesis and Orthopaedic Technology department under Faculty of Engineering / Technology.
UNIUYO Cut-Off Mark for Prosthesis and Orthopaedic Technology
The general UTME cut-off mark is 180, but due to the variation of Prosthesis and Orthopaedic Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from UNIUYO Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other UNIUYO Science Courses with their Requirements
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Crop Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Crop Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science,
one Science/Social Science subject and
at least a pass in Physics is required.
Medicine and Surgery
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medicine and Surgery department.
Building
SSCE Requirements
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Health Education
SSCE Requirements
To study this course, candidates aspiring to gain admission into Health Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Pharmacy
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Pharmacy department.
Teacher Education Science
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Teacher Education Science department.
any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Prosthesis and Orthopaedic Technology Course