If you are planning to study Automobile Engineering at Waziri Umaru Federal Polytechnic located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Waziri Umaru Federal Polytechnic.
Does Waziri Umaru Federal Polytechnic offer Automobile Engineering?
No, Waziri Umaru Federal Polytechnic does not offer Automobile Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Waziri Umaru Federal Polytechnic below to check if the Automobile Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Automobile Engineering When Accredited in Waziri Umaru Federal Polytechnic
O’Level Requirements
To study this course, candidates seeking admission into the Automobile Engineering department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Waziri Umaru Federal Polytechnic Cut-Off Mark for Automobile Engineering
The general UTME cut-off mark is 180, but due to the variation of Automobile Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Waziri Umaru Federal Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Waziri Umaru Federal Polytechnic Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building Technology (BT) department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates seeking admission into the Science Laboratory Technology (SLT) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Estate Management and Valuation
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Estate Management and Valuation department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Computer Science (CS)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Metallurgical Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Metallurgical Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
Nigerian Tertiary Institutions Offering Automobile Engineering Course