If you are planning to study Welding and Fabrication Technology at Waziri Umaru Federal Polytechnic located in Kebbi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Waziri Umaru Federal Polytechnic.
Does Waziri Umaru Federal Polytechnic offer Welding and Fabrication Technology?
No, Waziri Umaru Federal Polytechnic does not offer Welding and Fabrication Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Waziri Umaru Federal Polytechnic below to check if the Welding and Fabrication Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Welding and Fabrication Technology When Accredited in Waziri Umaru Federal Polytechnic
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Welding and Fabrication Technology department under Faculty of Engineering / Technology, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
JAMB Subject Combination
Physics/Technical Drawing or Chemistry.
Waziri Umaru Federal Polytechnic Cut-Off Mark for Welding and Fabrication Technology
The general UTME cut-off mark is 180, but due to the variation of Welding and Fabrication Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Waziri Umaru Federal Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Waziri Umaru Federal Polytechnic Science Courses with their Requirements
Estate Management and Valuation
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Estate Management and Valuation department.
Economics, Arts, Physics,
Technical Drawing, Chemistry and Biology
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Computer Science (CS)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Computer Science (CS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other Science subjects.
Agricultural Engineering / Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Agricultural Engineering / Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any three of the following:
Biology / Agricultural Science, Chemistry, Technical Drawing, Basic Electronics / Basic Electricity, Auto Mechanics, Metal Work, Further Mathematics, Food and Nutrition and Geography.
At least passes in Chemistry, Biology / Agricultural Science / Food and Nutrition.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Architectural Technology
SSCE Requirements
To study this course, candidates seeking admission into the Architectural Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Electrical / Electronic Engineering Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science Subject.
Nigerian Polytechnics Offering Welding and Fabrication Technology Course