If you are planning to study Metallurgical Engineering Technology at Abdu Gusau Polytechnic located in Zamfara State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Abdu Gusau Polytechnic.
Does Abdu Gusau Polytechnic offer Metallurgical Engineering Technology?
No, Abdu Gusau Polytechnic does not offer Metallurgical Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Abdu Gusau Polytechnic below to check if the Metallurgical Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Metallurgical Engineering Technology When Accredited in Abdu Gusau Polytechnic
O’Level Requirements
To study this course, candidates seeking admission into the Metallurgical Engineering Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work,
Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
JAMB Subject Combination
Chemistry, Physics or Technical Drawing
and any other relevant subject.
Abdu Gusau Polytechnic Cut-Off Mark for Metallurgical Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Metallurgical Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Abdu Gusau Polytechnic Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Abdu Gusau Polytechnic Science Courses with their Requirements
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Mechanical Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Statistics
SSCE Requirements
To study this course, candidates seeking admission into the Statistics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
Electrical / Electronic Engineering Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronic Engineering Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science Subject.
Computer Science (CS)
SSCE Requirements
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Architectural Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architectural Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Science Laboratory Technology (SLT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Science Laboratory Technology (SLT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Any two (2) subjects from: Physics, Chemistry, and Biology / Agricultural Science / Health Science
Any other two (2) relevant subjects (Technical Drawing, Metal / Wood Work, Basic Electricity, Geography, Further Mathematics, and Fine Art)
Nigerian Polytechnics Offering Metallurgical Engineering Technology Course