If you are planning to study Applied Biology and Biotechnology at Abia State University located in Abia State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABSU.
Does Abia State University (ABSU) offer Applied Biology and Biotechnology?
No, Abia State University does not offer Applied Biology and Biotechnology under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Abia State University (ABSU) below to check if the Applied Biology and Biotechnology course under the Faculty of Science has been updated.
Admission Requirements for Applied Biology and Biotechnology When Accredited in Abia State University (ABSU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Applied Biology and Biotechnology department under Faculty of Science, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
JAMB Subject Combination
either Physics or Mathematics.
ABSU Cut-Off Mark for Applied Biology and Biotechnology
The general UTME cut-off mark is 180, but due to the variation of Applied Biology and Biotechnology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABSU Science Courses with their Requirements
Public Health
SSCE Requirements
To study this course, candidates seeking admission into the Public Health department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Zoology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Zoology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subject.
Information and Communication Technology Engineering
SSCE Requirements
To study this course, candidates aspiring to gain admission into Information and Communication Technology Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two other relevant subject.
Environmental Science
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Environmental Science department.
For holders of NTC, the relevant subjects could be;
General Wood work, Building / Engineering, Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing,
Printing Origination, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Mechanical Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant Science subjects.
Nigerian Tertiary Institutions Offering Applied Biology and Biotechnology Course