If you are planning to study Physics and Applied Physics at Abia State University located in Abia State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABSU.
Does Abia State University (ABSU) offer Physics and Applied Physics?
No, Abia State University does not offer Physics and Applied Physics under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Abia State University (ABSU) below to check if the Physics and Applied Physics course under the Faculty of Science has been updated.
Admission Requirements for Physics and Applied Physics When Accredited in Abia State University (ABSU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Physics and Applied Physics department under Faculty of Science, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject from Further Mathematics and Biology or Agricultural Science.
ABSU Cut-Off Mark for Physics and Applied Physics
The general UTME cut-off mark is 180, but due to the variation of Physics and Applied Physics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABSU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABSU Science Courses with their Requirements
Anatomy
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Anatomy department.
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Urban and Regional Planning (URP) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Surveying and Geoinformatics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Zoology
SSCE Requirements
To study this course, candidates aspiring to gain admission into Zoology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
two (2) other Science subject.
Chemistry and Industrial Chemistry
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Chemistry and Industrial Chemistry department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Soil Science
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Soil Science department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology / Agricultural Science and
any other Science subject.
Environmental Science
SSCE Requirements
To study this course, candidates aspiring to gain admission into Environmental Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
For holders of NTC, the relevant subjects could be;
General Wood work, Building / Engineering, Drawing, Introduction to Building Construction, Decorative Painting, Spray Painting, Lining, Sign and Design, Wall hanging, Colour Mixing / Matching and Glazing,
Printing Origination, Machine Printing and Finishing, General Metal Work, Basic Electricity, Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Graphic Design, Graphic Printing and Ceramics.
Nigerian Tertiary Institutions Offering Physics and Applied Physics Course