If you are planning to study Building at Abubakar Tafawa Balewa University located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ATBU was established in 1980 as a Federal University of Technology and later renamed to promote science and engineering education in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into ATBU.
Does Abubakar Tafawa Balewa University (ATBU) offer Building?
No, Abubakar Tafawa Balewa University does not offer Building under its Faculty of Built Environment. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tafawa Balewa University (ATBU) below to check if the Building course under the Faculty of Built Environment has been updated.
Admission Requirements for Building When Accredited in Abubakar Tafawa Balewa University (ATBU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Building department under Faculty of Built Environment, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
ATBU Cut-Off Mark for Building
The general UTME cut-off mark is 180, but due to the variation of Building cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATBU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATBU Science Courses with their Requirements
1. Woodwork Technology Education
To study this course, the minimum requirement for applicants seeking admission to the Woodwork Technology Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one (1) of Biology / Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
2. Computer and Communication Engineering
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer and Communication Engineering department.
3. Electrical / Electronics Engineering
To study this course, candidates aspiring to gain admission into Electrical / Electronics Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
4. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
5. Education and Integrated Science
To study this course, candidates seeking admission into the Education and Integrated Science department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Any other four (4) relevant subjects
6. Education and Computer Science
To study this course, candidates seeking admission into the Education and Computer Science department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
three (3) other relevant Science subjects.
7. Building Technology Education
To study this course, candidates aspiring to gain admission into Building Technology Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
Nigerian Universities Offering Building Course