If you are planning to study Industrial Mathematics at Abubakar Tafawa Balewa University located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ATBU.
Does Abubakar Tafawa Balewa University (ATBU) offer Industrial Mathematics?
No, Abubakar Tafawa Balewa University does not offer Industrial Mathematics under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tafawa Balewa University (ATBU) below to check if the Industrial Mathematics course under the Faculty of Science has been updated.
Admission Requirements for Industrial Mathematics When Accredited in Abubakar Tafawa Balewa University (ATBU)
O’Level Requirements
To study this course, candidates seeking admission into the Industrial Mathematics department under Faculty of Science, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
two (2) other Science subjects.
JAMB Subject Combination
any two (2) other subjects from
Physics, Chemistry, Economics,
Biology and Agricultural Science.
ATBU Cut-Off Mark for Industrial Mathematics
The general UTME cut-off mark is 180, but due to the variation of Industrial Mathematics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATBU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATBU Science Courses with their Requirements
1. Mechanical Engineering
To study this course, the minimum requirement for applicants seeking admission to the Mechanical Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant Science subjects.
2. Physics and Applied Physics
To study this course, candidates aspiring to gain admission into Physics and Applied Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject from Further Mathematics and Biology or Agricultural Science.
3. Automobile Technology Education
To study this course, candidates seeking admission into the Automobile Technology Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology /Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
4. Mechatronics and System Engineering
To study this course, candidates aspiring to gain admission into Mechatronics and System Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
5. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
6. Petrochemical Engineering
To study this course, candidates seeking admission into the Petrochemical Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other relevant subject.
7. Architecture
To study this course, candidates aspiring to gain admission into Architecture department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Nigerian Universities Offering Industrial Mathematics Course