If you are planning to study Mathematics and Education Technology at Abubakar Tafawa Balewa University located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ATBU was established in 1980 as a Federal University of Technology and later renamed to promote science and engineering education in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into ATBU.
Does Abubakar Tafawa Balewa University (ATBU) offer Mathematics and Education Technology?
No, Abubakar Tafawa Balewa University does not offer Mathematics and Education Technology under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tafawa Balewa University (ATBU) below to check if the Mathematics and Education Technology course under the Faculty of Education has been updated.
Admission Requirements for Mathematics and Education Technology When Accredited in Abubakar Tafawa Balewa University (ATBU)
O’Level Requirements
To study this course, candidates seeking admission into the Mathematics and Education Technology department under Faculty of Education, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
three (3) more pertinent science subjects in not more than two (2) sittings.
JAMB Subject Combination
one (1) other Science Subject.
ATBU Cut-Off Mark for Mathematics and Education Technology
The general UTME cut-off mark is 180, but due to the variation of Mathematics and Education Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATBU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATBU Science Courses with their Requirements
1. Building Technology Education
To study this course, candidates seeking admission into the Building Technology Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
2. Geophysics
To study this course, candidates seeking admission into the Geophysics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
3. Agricultural Science and Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Science and Education department.
Biology/Agricultural Science,
any other relevant subject.
4. Applied Botany
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Applied Botany department.
and any one (1) of Health Science, Statistics, Physics and Geography.
5. Quantity Surveying (QS)
To study this course, candidates aspiring to gain admission into Quantity Surveying (QS) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
6. Mechanical / Production Engineering
To study this course, candidates seeking admission into the Mechanical / Production Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
7. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Nigerian Tertiary Institutions Offering Mathematics and Education Technology Course