If you are planning to study Mechanical Metalwork Technology Education at Abubakar Tafawa Balewa University located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ATBU.
Does Abubakar Tafawa Balewa University (ATBU) offer Mechanical Metalwork Technology Education?
No, Abubakar Tafawa Balewa University does not offer Mechanical Metalwork Technology Education under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tafawa Balewa University (ATBU) below to check if the Mechanical Metalwork Technology Education course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical Metalwork Technology Education When Accredited in Abubakar Tafawa Balewa University (ATBU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical Metalwork Technology Education department under Faculty of Engineering / Technology.
one (1) of Biology /Agricultural Science; Physics, or Chemistry and
two (2) from General Science/IntegratedScience, Technical Drawing/Fine Art, Health Science Food and Nutrition,
Geography, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
JAMB Subject Combination
any other relevant subject.
ATBU Cut-Off Mark for Mechanical Metalwork Technology Education
The general UTME cut-off mark is 180, but due to the variation of Mechanical Metalwork Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATBU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATBU Science Courses with their Requirements
Mathematics
SSCE Requirements
To study this course, candidates aspiring to gain admission into Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
Architecture
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
Applied Botany
SSCE Requirements
To study this course, candidates aspiring to gain admission into Applied Botany department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
and any one (1) of Health Science, Statistics, Physics and Geography.
Education and Chemistry
SSCE Requirements
To study this course, candidates aspiring to gain admission into Education and Chemistry department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology and Agricultural Science.
Civil Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Civil Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Electrical / Electronics Engineering
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Electrical / Electronics Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any other Science subject.
Woodwork / Education
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Woodwork / Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any one (1) of Biology / Agricultural Science; Physics, or Chemistry
and two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
Nigerian Tertiary Institutions Offering Mechanical Metalwork Technology Education Course