If you are planning to study Shipping and Maritime Technology at Abubakar Tafawa Balewa University located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ATBU was established in 1980 as a Federal University of Technology and later renamed to promote science and engineering education in Nigeria. This page explains everything you need to know to increase your chances of gaining admission into ATBU.
Does Abubakar Tafawa Balewa University (ATBU) offer Shipping and Maritime Technology?
No, Abubakar Tafawa Balewa University does not offer Shipping and Maritime Technology under its Faculty of Maritime Studies. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tafawa Balewa University (ATBU) below to check if the Shipping and Maritime Technology course under the Faculty of Maritime Studies has been updated.
Admission Requirements for Shipping and Maritime Technology When Accredited in Abubakar Tafawa Balewa University (ATBU)
O’Level Requirements
To study this course, the minimum requirement for applicants seeking admission to the Shipping and Maritime Technology department under Faculty of Maritime Studies, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
one (1) other subject (not more than two (2) sittings) from:
ATBU Cut-Off Mark for Shipping and Maritime Technology
The general UTME cut-off mark is 180, but due to the variation of Shipping and Maritime Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATBU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATBU Science Courses with their Requirements
1. Automobile Technology Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Automobile Technology Education department.
Biology /Agricultural Science, Physics, or Chemistry and
two (2) from General Science / Integrated Science, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition, Physical and Health Education, Auto Technical, Building, Electrical Electronic, Metal Work and Wood Work.
2. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
3. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
4. Civil Engineering
To study this course, candidates seeking admission into the Civil Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
5. Geophysics
To study this course, candidates aspiring to gain admission into Geophysics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
6. Physics and Applied Physics
To study this course, candidates aspiring to gain admission into Physics and Applied Physics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject from Further Mathematics and Biology or Agricultural Science.
7. Electrical / Electronics Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Electrical / Electronics Education department.
any other Science subject.
Nigerian Tertiary Institutions Offering Shipping and Maritime Technology Course