If you are planning to study Mineral and Petroleum Resources Engineering Technology at Abubakar Tatari Ali Polytechnic located in Bauchi State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ATAP.
Does Abubakar Tatari Ali Polytechnic (ATAP) offer Mineral and Petroleum Resources Engineering Technology?
No, Abubakar Tatari Ali Polytechnic does not offer Mineral and Petroleum Resources Engineering Technology under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Abubakar Tatari Ali Polytechnic (ATAP) below to check if the Mineral and Petroleum Resources Engineering Technology course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mineral and Petroleum Resources Engineering Technology When Accredited in Abubakar Tatari Ali Polytechnic (ATAP)
O’Level Requirements
To study this course, candidates seeking admission into the Mineral and Petroleum Resources Engineering Technology department under Faculty of Engineering / Technology, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Woodwork for Civil Engineering Technology, Further Mathematics, English Language, Geography, Economics/Commerce,
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work.
JAMB Subject Combination
Chemistry or Technical Drawing.
ATAP Cut-Off Mark for Mineral and Petroleum Resources Engineering Technology
The general UTME cut-off mark is 180, but due to the variation of Mineral and Petroleum Resources Engineering Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ATAP Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ATAP Science Courses with their Requirements
Civil Engineering Technology
SSCE Requirements
To study this course, candidates seeking admission into the Civil Engineering Technology department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one other subject from:
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography and Economics/Commerce.
For Marine Engineering and Industrial Safety & Environmental Engineering a pass in Biology is required.
Welding and Fabrication Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Welding and Fabrication Technology department.
Biology/Agricultural Science, Technical Drawing, Basic Electronics/Basic Electricity, Auto Mechanics, Metal Work, Woodwork (for Civil Engineering Tech.), Further Mathematics, English Language, Geography, Economics/Commerce.
At least a credit pass in English Language is required.
Building Technology (BT)
SSCE Requirements
To study this course, candidates aspiring to gain admission into Building Technology (BT) department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be; Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Architectural Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Architectural Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology, Fine Art, Chemistry, History, English Language, Geography, Further Mathematics, Economics / Commerce, Religious Knowledge, Technical Drawing and Business Method.
At least a pass in Fine Art or Technical Drawing.
Agricultural Technology
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Technology department.
Biology / Agricultural Science,
Mathematics, Chemistry and
Geography, Food and Nutrition, Economics,
Technical Drawing, Physics, Nigerian Language and Home Economics.
Computer Science (CS)
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
Production Technology
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Production Technology department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology/Agricultural Science,
any other relevant subject from the following:
Technical Drawing, Physics,
Nigerian Language, Home Economics.
Nigerian Polytechnics Offering Mineral and Petroleum Resources Engineering Technology Course