If you are planning to study Computer Science and Information Technology at Ahmadu Bello University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into ABU.
Does Ahmadu Bello University (ABU) offer Computer Science and Information Technology?
No, Ahmadu Bello University does not offer Computer Science and Information Technology under its Faculty of Data and Decision Sciences. However, since our course list is updated regularly, you can visit the courses available at Ahmadu Bello University (ABU) below to check if the Computer Science and Information Technology course under the Faculty of Data and Decision Sciences has been updated.
Admission Requirements for Computer Science and Information Technology When Accredited in Ahmadu Bello University (ABU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science and Information Technology department under Faculty of Data and Decision Sciences.
two (2) other Science subjects.
JAMB Subject Combination
Agric Science, Economics and Geography.
ABU Cut-Off Mark for Computer Science and Information Technology
The general UTME cut-off mark is 180, but due to the variation of Computer Science and Information Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABU Science Courses with their Requirements
1. Glass Technology
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Glass Technology department.
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
2. Agricultural Science and Education
To study this course, candidates seeking admission into the Agricultural Science and Education department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Biology/Agricultural Science,
any other relevant subject.
3. Surveying and Geoinformatics
To study this course, candidates seeking admission into the Surveying and Geoinformatics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
6. Mechatronics Engineering
To study this course, candidates seeking admission into the Mechatronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
7. Physical and Health Education
To study this course, the minimum requirement for applicants seeking admission to the Physical and Health Education department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Biology or its equivalent
and any two (2) other relevant subjects.
Nigerian Tertiary Institutions Offering Computer Science and Information Technology Course