If you are planning to study Mathematics and Economics at Ahmadu Bello University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ABU was established in 1962 as one of Nigeria’s premier federal universities to promote higher education, research, and national development. This page explains everything you need to know to increase your chances of gaining admission into ABU.
Does Ahmadu Bello University (ABU) offer Mathematics and Economics?
No, Ahmadu Bello University does not offer Mathematics and Economics under its Faculty of Science. However, since our course list is updated regularly, you can visit the courses available at Ahmadu Bello University (ABU) below to check if the Mathematics and Economics course under the Faculty of Science has been updated.
Admission Requirements for Mathematics and Economics When Accredited in Ahmadu Bello University (ABU)
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mathematics and Economics department under Faculty of Science.
any other two (2) subjects selected from:
Science or Social Sciences at not more than two (2) sittings.
JAMB Subject Combination
any other Science or Social Science subject.
ABU Cut-Off Mark for Mathematics and Economics
The general UTME cut-off mark is 180, but due to the variation of Mathematics and Economics cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABU Science Courses with their Requirements
1. Automotive Engineering
To study this course, candidates seeking admission into the Automotive Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
2. Radiography
To study this course, candidates seeking admission into the Radiography department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
3. Computer Science (CS)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Computer Science (CS) department.
any two (2) other Science subjects.
4. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
5. Medicine and Surgery
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Medicine and Surgery department.
6. Physical and Health Education
To study this course, candidates aspiring to gain admission into Physical and Health Education department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Biology or its equivalent
and any two (2) other relevant subjects.
7. Agricultural Engineering (AE)
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Agricultural Engineering (AE) department.
Any one other subject from:
Introduction to Agricultural Science,
Materials and Workshop Process and Machining,
Tractor Layout Power Unit Under Carriage and Auto Electricity;
Transmission System;
Implement and Machine;
Principles of Crop Husbandry and Land Use,
Materials and Workshop Processes;
Construction and Maintenance of Agricultural Machines;
General Metal Work;
General Wood Work and Building / Engineering Drawing.
Nigerian Tertiary Institutions Offering Mathematics and Economics Course