If you are planning to study Polymer and Textile Engineering at Ahmadu Bello University located in Kaduna State, it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. ABU was established in 1962 as one of Nigeria’s premier federal universities to promote higher education, research, and national development. This page explains everything you need to know to increase your chances of gaining admission into ABU.
Does Ahmadu Bello University (ABU) offer Polymer and Textile Engineering?
No, Ahmadu Bello University does not offer Polymer and Textile Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Ahmadu Bello University (ABU) below to check if the Polymer and Textile Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Polymer and Textile Engineering When Accredited in Ahmadu Bello University (ABU)
O’Level Requirements
To study this course, candidates aspiring to gain admission into Polymer and Textile Engineering department under Faculty of Engineering / Technology, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any other Science subject.
ABU Cut-Off Mark for Polymer and Textile Engineering
The general UTME cut-off mark is 180, but due to the variation of Polymer and Textile Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from ABU Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other ABU Science Courses with their Requirements
1. Forestry and Wildlife Management
To study this course, candidates seeking admission into the Forestry and Wildlife Management department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Further Mathematics and Statistics.
2. Surveying and Geoinformatics
To study this course, candidates aspiring to gain admission into Surveying and Geoinformatics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
3. Architecture
To study this course, the minimum requirement for applicants seeking admission to the Architecture department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
4. Physical and Health Education
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Physical and Health Education department.
Biology or its equivalent
and any two (2) other relevant subjects.
5. Civil Engineering
To study this course, the minimum requirement for applicants seeking admission to the Civil Engineering department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
6. Education and Computer Science
To study this course, candidates aspiring to gain admission into Education and Computer Science department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
three (3) other relevant Science subjects.
7. Glass Technology
To study this course, candidates aspiring to gain admission into Glass Technology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
Spinning, Weaving, Surface Design and Printing, Bleaching, Dyeing and Finishing, Ceramics, Graphic Design, Graphic Printing, Decorative Painting,
Spray Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Building / Engineering Drawing, General Wood Work.
Nigerian Tertiary Institutions Offering Polymer and Textile Engineering Course