If you are planning to study Auto and Mechanical Technology Education at Baze University located in Federal Capital Territory (FCT), it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Baze University.
Does Baze University offer Auto and Mechanical Technology Education?
No, Baze University does not offer Auto and Mechanical Technology Education under its Faculty of Education. However, since our course list is updated regularly, you can visit the courses available at Baze University below to check if the Auto and Mechanical Technology Education course under the Faculty of Education has been updated.
Admission Requirements for Auto and Mechanical Technology Education When Accredited in Baze University
O’Level Requirements
To study this course, candidates seeking admission into the Auto and Mechanical Technology Education department under Faculty of Education, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any one (1) of Biology / Agricultural Science; Physics, or Chemistry,
Auto Technical, Technical Drawing / Fine Art, Geography, Health Science Food and Nutrition,
Physical and Health Education, General Science / Integrated Science, Building, Electrical Electronic, Metal Work and Wood Work.
Baze University Cut-Off Mark for Auto and Mechanical Technology Education
The general UTME cut-off mark is 180, but due to the variation of Auto and Mechanical Technology Education cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Baze University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Baze University Science Courses with their Requirements
1. Urban and Regional Planning (URP)
To study this course, the minimum requirement for applicants seeking admission to the Urban and Regional Planning (URP) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
2. Petroleum Engineering
To study this course, candidates aspiring to gain admission into Petroleum Engineering department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
3. Surveying and Geoinformatics
To study this course, the minimum requirement for applicants seeking admission to the Surveying and Geoinformatics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
4. Computer Science (CS)
To study this course, the minimum requirement for applicants seeking admission to the Computer Science (CS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other Science subjects.
5. Architecture
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Architecture department.
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall,
Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, and Basic Electricity
6. Building
To study this course, candidates seeking admission into the Building department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
7. Quantity Surveying (QS)
To study this course, candidates seeking admission into the Quantity Surveying (QS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
Nigerian Tertiary Institutions Offering Auto and Mechanical Technology Education Course