If you are planning to study Forestry and Wood Technology at Baze University located in Federal Capital Territory (FCT), it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. Baze University was established in 2011 as a private university in Abuja to provide quality higher education with emphasis on entrepreneurship, leadership, and innovation. This page explains everything you need to know to increase your chances of gaining admission into Baze University.
Does Baze University offer Forestry and Wood Technology?
No, Baze University does not offer Forestry and Wood Technology under its Faculty of Agriculture. However, since our course list is updated regularly, you can visit the courses available at Baze University below to check if the Forestry and Wood Technology course under the Faculty of Agriculture has been updated.
Admission Requirements for Forestry and Wood Technology When Accredited in Baze University
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Forestry and Wood Technology department under Faculty of Agriculture.
Biology / Agricultural Science,
at least ‘O’ Level pass in Physics.
JAMB Subject Combination
Mathematics / Physics and
Biology / Agricultural Science.
Baze University Cut-Off Mark for Forestry and Wood Technology
The general UTME cut-off mark is 180, but due to the variation of Forestry and Wood Technology cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Baze University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Baze University Science Courses with their Requirements
1. Civil Engineering
To study this course, candidates seeking admission into the Civil Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
2. Mathematics
To study this course, candidates aspiring to gain admission into Mathematics department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
any two (2) other relevant subjects.
3. Quantity Surveying (QS)
To study this course, the minimum requirement for applicants seeking admission to the Quantity Surveying (QS) department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any of Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further. Mathematics, Introduction to Building Construction, Bricklaying / Block laying, Concreting, Wall, Floors and Ceiling Finishing, Joinery, Carpentary, Decorative Painting, Lining, Sign and Design, Wall Hanging, Colour Mixing / Matching and Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity.
4. Human Physiology
To study this course, candidates aspiring to gain admission into Human Physiology department, should at least obtain five (5) credit (C5 and above) passes in their SSCE subjects including:
5. Surveying and Geoinformatics
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
6. Building
To study this course, the minimum requirement for applicants seeking admission to the Building department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
7. Computer Science (CS)
To study this course, candidates seeking admission into the Computer Science (CS) department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other Science subjects.
Nigerian Tertiary Institutions Offering Forestry and Wood Technology Course