If you are planning to study Mechanical and Metallurgical Engineering at Baze University located in Federal Capital Territory (FCT), it is important to understand the admission requirements, cut-off mark, and career opportunities before applying. This page explains everything you need to know to increase your chances of gaining admission into Baze University.
Does Baze University offer Mechanical and Metallurgical Engineering?
No, Baze University does not offer Mechanical and Metallurgical Engineering under its Faculty of Engineering / Technology. However, since our course list is updated regularly, you can visit the courses available at Baze University below to check if the Mechanical and Metallurgical Engineering course under the Faculty of Engineering / Technology has been updated.
Admission Requirements for Mechanical and Metallurgical Engineering When Accredited in Baze University
O’Level Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Mechanical and Metallurgical Engineering department under Faculty of Engineering / Technology.
one (1) other Science subject.
Baze University Cut-Off Mark for Mechanical and Metallurgical Engineering
The general UTME cut-off mark is 180, but due to the variation of Mechanical and Metallurgical Engineering cut-off mark depending on the admission year and competition level, we suggest you enquire about the recent JAMB UTME cut-off mark from Baze University Officials. However, to improve your admission chances:
Perform well in Post-UTME screening.
Other Baze University Science Courses with their Requirements
Urban and Regional Planning (URP)
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Urban and Regional Planning (URP) department.
Physics, Chemistry, Economics, Government, Biology, Art, History, IRK/CRK, Social Studies and Tech Drawing.
Building
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Building department.
Geography, Economics, Arts and Technical drawing.
For holders of NTC, the other relevant subjects could be;
Intro. to Building Construction, Bricklaying, Concreting, Walls, Floors and Ceiling Finishing, Building / Engineering Drawing, Joinery, Carpentry, Gas, Steam Work and Bronze Welding, Cold / Hot Water Supply, Sanitation and Drainage.
Electrical / Electronics Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Electrical / Electronics Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any other Science subject.
Mathematics
SSCE Requirements
To study this course, the minimum requirement for applicants seeking admission to the Mathematics department, is five (5) credits (C5 and higher) in their SSCE subjects, including the following:
any two (2) other relevant subjects.
Surveying and Geoinformatics
SSCE Requirements
To study this course, a minimum of five (5) credit passes (C5 and higher) in their SSCE subjects, including the following, are required for applicants to the Surveying and Geoinformatics department.
Joinery, Carpentry, Decorative Painting, Lining, Sign & Design, Wall Hanging, Colour Mixing / Matching & Glazing, Ceramics, Graphics Design, Graphic Printing, Basic Electricity,
Fine Art, Geography or Wood Work, Biology, Economics, Technical Drawing, Further Mathematics, Introduction to Building Construction, Bricklaying / Block Laying, Concreting, Wall, Floors and Ceiling Finishing.
Telecommunication Engineering
SSCE Requirements
To study this course, candidates seeking admission into the Telecommunication Engineering department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
any two (2) other relevant subjects.
Physics
SSCE Requirements
To study this course, candidates seeking admission into the Physics department, must have at least five (5) credits (C5 and more) in their SSCE disciplines, including the following:
Chemistry, Mathematics and
any other Science subject from
Biology / Agricultural Science.
Nigerian Tertiary Institutions Offering Mechanical and Metallurgical Engineering Course